Linksys Extender Not Connecting to the Internet? Let’s Fix It!


If your Linksys extender is not connecting to the internet then let us tell you that you are not alone in the battle. This issue is faced by every 2nd Linksys extender user across the world. Here, in this post, we will guide you on how to fix the issue within minutes. Let’s get the ball rolling!

Before delving into the troubleshooting tips to fix the issue, it is important for you to know the reasons behind it. There can be various reasons behind Linksys extender not connecting to the internet issue. A few of them are listed below:

  • Loose cable connections
  • Incomplete Linksys extender setup
  • Faulty hardware
  • Outdated firmware on Linksys extender
  • WiFi or signal interference with Linksys extender
  • No internet
  • Linksys extender showing red light
  • The extender is placed in a poor location
  • Default extender.linksys.setup settings 

That’s it! These were some reasons causing Linksys extender not connecting to the internet issue. Now, let’s take the plunge to solve this, shall we?

Fixed: Linksys Extender Not Connecting to the Internet Issue

Connect Your Linksys Extender Correctly

If you are not aware of the process to connect your Linksys extender to your router then you will surely bump into the issue. So, to connect your Linksys extender correctly, have a quick look at the steps highlighted below:

  • Plug in your Linksys extender near to your router.
  • Then, grab an Ethernet cable and connect your router and the Linksys extender with each other properly.
  • Thereafter, turn on a PC or laptop.
  • Open an internet browser as per your choice.
  • Hover your mouse cursor over the browser’s address bar and navigate to the extender.linksys.setup page.

If the setup page loads up quickly then you have successfully connected your router and the Linksys extender. In the event that the web page takes more than ages to load then head over to the next troubleshooting tip.

Place Your Linksys Extender Correctly

While placing your Linksys extender, keep the following tips into consideration:

  • Place your Linksys extender at the central location of your home.
  • Keep the extender away from corners and the reach of neighboring WiFi.
  • Place the extender on a higher and clean location.
  • Do not place your Linksys extender inside a cabinet, behind a device or under a table.
  • Place your Linksys extender at a location where it can easily receive 50 percent of your router’s WiFi signals.

Check the Wired Connections

If the issue continues to trouble you then check the cable connection you have made between your Linksys extender and router. The cable connection must be accurate and finger-tight. Also, check that the Ethernet cable you are using is in good condition. On the off chance if the Ethernet connection does not work for you, try connecting your devices in a wireless manner.

After creating a strong connection between your devices, try accessing the Linksys range extender login page using the default IP.

Power Cycle Your Linksys Extender

If none of the aforementioned troubleshooting tips worked for you, then it is recommended to give your Linksys extender a fresh start. To power cycle your Linksys extender, do the following:

Disconnect your Linksys extender from your router and then unplug it from the wall socket.

Wait for some time and then plug in back your Linksys extender.

Update Extender’s Firmware

An outdated Linksys extender firmware version will never let you take the most out of its WiFi. So, it’s better to update the firmware of your Linksys extender timely.

  • Connect your WiFi-enabled device to Linksys extender setup-xxx.
  • Visit the Linksys official site.
  • Enter your Linksys extender model number.
  • Check the updates available for your Linksys extender.
  • If you found any, update it by applying the on-screen instructions.

Still Linksys Extender Not Connecting to the Internet?

Don’t sweat over it! Get in touch with our technical experts right away and let them fix the issue for you in no time.